Tutorial Microcontroller MCS-51 ATMEL ISP
 

 

Super MCS51 Trainer

Standart MCS51 Trainer

Standart AVR Trainer

Programmer USBASP

Standart ARM Trainer

 

 

Working with stm32f407 ADC+TIMER+DMA

 

#include "stm32f4_discovery.h"

void RCC_Configuration(void)
{
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2, ENABLE);
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOC, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC2, ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
}

/***************************************************************************/
void GPIO_Configuration(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
/* ADC Channel 10 -> PC0
ADC Channel 11 -> PC1
*/
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 | GPIO_Pin_1;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AN;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL ;
GPIO_Init(GPIOC, &GPIO_InitStructure);
}
/***************************************************************************/
void ADC_Configuration(void)
{
ADC_CommonInitTypeDef ADC_CommonInitStructure;
ADC_InitTypeDef ADC_InitStructure;
/* ADC Common Init */
ADC_CommonInitStructure.ADC_Mode = ADC_DualMode_RegSimult;
ADC_CommonInitStructure.ADC_Prescaler = ADC_Prescaler_Div2;
ADC_CommonInitStructure.ADC_DMAAccessMode = ADC_DMAAccessMode_1;
// 2 half-words one by one, 1 then 2
ADC_CommonInitStructure.ADC_TwoSamplingDelay = ADC_TwoSamplingDelay_5Cycles;
ADC_CommonInit(&ADC_CommonInitStructure);
ADC_InitStructure.ADC_Resolution = ADC_Resolution_12b;
ADC_InitStructure.ADC_ScanConvMode = DISABLE; // 1 Channel
ADC_InitStructure.ADC_ContinuousConvMode = DISABLE; // Conversions Triggered
ADC_InitStructure.ADC_ExternalTrigConvEdge = ADC_ExternalTrigConvEdge_Rising;
ADC_InitStructure.ADC_ExternalTrigConv = ADC_ExternalTrigConv_T2_TRGO;
ADC_InitStructure.ADC_DataAlign = ADC_DataAlign_Right;
ADC_InitStructure.ADC_NbrOfConversion = 1;
ADC_Init(ADC1, &ADC_InitStructure);
ADC_Init(ADC2, &ADC_InitStructure); // Mirror on ADC2
/* ADC1 regular channel 10 configuration */
ADC_RegularChannelConfig(ADC1, ADC_Channel_10, 1,
ADC_SampleTime_15Cycles);
// PC0

/* ADC2 regular channel 11 configuration */
ADC_RegularChannelConfig(ADC2, ADC_Channel_11, 1,
ADC_SampleTime_15Cycles);
// PC1
/* Enable DMA request after last transfer (Multi-ADC mode) */
ADC_MultiModeDMARequestAfterLastTransferCmd(ENABLE);
/* Enable ADC1 */
ADC_Cmd(ADC1, ENABLE);
/* Enable ADC2 */
ADC_Cmd(ADC2, ENABLE);
}

/**************************************************************************/
# define BUFFERSIZE 800 // I+Q 200KHz x2 HT/TC at 1KHz

__IO uint16_t ADCDualConvertedValues[BUFFERSIZE]; // Filled as pairs ADC1, ADC2

static void DMA_Configuration(void)
{
DMA_InitTypeDef DMA_InitStructure;

DMA_InitStructure.DMA_Channel = DMA_Channel_0;
DMA_InitStructure.DMA_Memory0BaseAddr = (uint32_t)&ADCDualConvertedValues;
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)0x40012308;
// CDR_ADDRESS; Packed ADC1, ADC2
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralToMemory;
DMA_InitStructure.DMA_BufferSize = BUFFERSIZE; // Count of 16-bit words
DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;
DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;
DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_HalfWord;
DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_HalfWord;
DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;
DMA_InitStructure.DMA_Priority = DMA_Priority_High;
DMA_InitStructure.DMA_FIFOMode = DMA_FIFOMode_Enable;
DMA_InitStructure.DMA_FIFOThreshold = DMA_FIFOThreshold_HalfFull;
DMA_InitStructure.DMA_MemoryBurst = DMA_MemoryBurst_Single;
DMA_InitStructure.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;
DMA_Init(DMA2_Stream0, &DMA_InitStructure);
/* Enable DMA Stream Half / Transfer Complete interrupt */
DMA_ITConfig(DMA2_Stream0, DMA_IT_TC | DMA_IT_HT, ENABLE);
/* DMA2_Stream0 enable */
DMA_Cmd(DMA2_Stream0, ENABLE);
}
void TIM2_Configuration(void)
{
TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
/* Time base configuration */
TIM_TimeBaseStructInit(&TIM_TimeBaseStructure);
TIM_TimeBaseStructure.TIM_Period = (84000000 / 200000) - 1;
// 200 KHz, from 84 MHz TIM2CLK (ie APB1 = HCLK/4, TIM2CLK = HCLK/2)
TIM_TimeBaseStructure.TIM_Prescaler = 0;
TIM_TimeBaseStructure.TIM_ClockDivision = 0;
TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;
TIM_TimeBaseInit(TIM2, &TIM_TimeBaseStructure);
/* TIM2 TRGO selection */
TIM_SelectOutputTrigger(TIM2, TIM_TRGOSource_Update);
// ADC_ExternalTrigConv_T2_TRGO
 /* TIM2 enable counter */
  TIM_Cmd(TIM2, ENABLE);
}
           
/****************************************************************************/            
void NVIC_Configuration(void)
{
 NVIC_InitTypeDef NVIC_InitStructure; 
           /* Enable the DMA Stream IRQ Channel */
  NVIC_InitStructure.NVIC_IRQChannel = DMA2_Stream0_IRQn;
  NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
  NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
  NVIC_Init(&NVIC_InitStructure);
}
           
/***********************************************************************/
void DMA2_Stream0_IRQHandler(void)//Called at 1 KHz for 200 KHz sample rate
{
 /* Test on DMA Stream Half Transfer interrupt */
 if(DMA_GetITStatus(DMA2_Stream0, DMA_IT_HTIF0))
 {
  /* Clear DMA Stream Half Transfer interrupt pending bit */
  DMA_ClearITPendingBit(DMA2_Stream0, DMA_IT_HTIF0); 
  /* Turn LED3 off: Half Transfer */
  STM_EVAL_LEDOff(LED3); 
  // Add code here to process first half of buffer (ping)
 }
           
 /* Test on DMA Stream Transfer Complete interrupt */
 if(DMA_GetITStatus(DMA2_Stream0, DMA_IT_TCIF0))
 {
  /* Clear DMA Stream Transfer Complete interrupt pending bit */
  DMA_ClearITPendingBit(DMA2_Stream0, DMA_IT_TCIF0);
  /* Turn LED3 on: End of Transfer */
  STM_EVAL_LEDOn(LED3); 
  // Add code here to process second half of buffer (pong)
  }
 }
           
 /*****************************************************************************/
           
 int main(void)
 {
  RCC_Configuration(); 
  GPIO_Configuration(); 
  NVIC_Configuration(); 
  TIM2_Configuration(); 
  DMA_Configuration(); 
  ADC_Configuration();
  STM_EVAL_LEDInit(LED3); /* Configure LEDs to monitor program status            */
  STM_EVAL_LEDOn(LED3); /* Turn LED3 on, 500 Hz means it working */ 
  /* Start ADC1 Software Conversion */
  ADC_SoftwareStartConv(ADC1);
           
  while(1); // Don't want to exit
 } 
 /***************************************************************************/
}