Tutorial Microcontroller MCS-51 ATMEL ISP

Pelatihan Dasar Mikrokontroller
14-15 April 2007
Surabaya
Rp. 300.000

Microcontroller Kits

Programmer and Target 89s51
Rp.100.000
(USD $10)

Simple Mikrokontroller 89s51 Trainer
Rp, 350.000
(USD $35)

Standart
Mikrokontroller 89s51 Trainer
Rp. 650.000
(USD $65)

Super Mikrokontroller Trainer 89s51
Rp.1.250.000
(USD $125)

ISP Flash Microcontroller Programmer
By : Asim Khan

Introduction
This ISP Programmer can be used either for in-system programming or as a stand-alone spi programmer for Atmel ISP programmable devices. The programming interface is compatible to STK200 ISP programmer hardware so the users of STK200 can also use the software which can program both the 8051 and AVR series devices.

Hardware
Figure 1 shows the circuit diagram of the in-system programmer interface, the power to the interface is provided by the target system. The 74245 ic isolate and buffer the parallel port signals.

Software
The ISP-30a.zip file contains the main program and the i/o port driver. Place all files in the same folder.
The main screen view of the program is shown in figure 3. Also make sure do not program the RSTDISBL fuse in ATmega8, ATtiny26 and ATtiny2313 otherwise further spi programming is disable and you will need a parallel programmer to enable the spi programming. For the fuses setting consult the datasheet of the respective device.

For the auto hardware detection it is necessary to short pin 2 and 12 of DB25 connector, otherwise the software uses the default parallel port i.e. LPT1.

Following are the main features of this software,

Read and write the Intel Hex file
Read signature, lock and fuse bits
Clear and Fill memory buffer
Verify with memory buffer
Reload current Hex file
Display buffer checksum
Program selected lock bits & fuses
Auto detection of hardware

Note:
The memory buffer contains both the code data and the eeprom data for the devices which have eeprom memory. The eeprom memory address in buffer is started after the code memory, so it is necessary the hex file should contains the eeprom start address after the end of code memory last address i.e. for 90S2313 the start address for eeprom memory is 0x800.

The software does not provide the erase command because this function is performed automatically during device programming. If you are required to erase the controller, first use the clear buffer command then program the controller, this will erase the controller and also set the AVR device fuses to default setting.

Download:
ISP-Flash Programmer Software ISP-30a.zip
ISP-Flash Programmer Schematic 89s-2(Buffer).pdf

Comments, questions and discussion about this topic

BACK

Pay per click

Programmer
ISP 89s

Free Software
a. Edsim 51
b. MIDE-51
c. ATMEL ISP

Lesson 1:
Architecture
1.1.Memory
1.2.SFR
1.3.Addressing
1.4.Instruction Set
1.5.Assignment

Lesson 2:
Input Output
2.1.LED
2.2.Swicht
2.3.7 Segmen
2.4.LCD Character
2.5.ADC
2.6.DAC
2.7.Motor Stepper
2.8.Keypad
2.9.Assignment

Lesson 3:
Timer Counter
3.1.Basic
3.2.Mode 0
3.3.Mode 1
3.4.Mode 2
3.5.Mode 3
3.5.Assignment

Lesson 4:
Serial Comm.
4.1.Basic
4.2.LED
4.3.Rotate LED
4.2 ADC
4.3.LCD
4.4.Assignment

Lesson 5:
Interuption
5.1.Basic
5.2.Timer
5.2.External
5.3.Assignment